Scotsman CME650R Instrukcja Obsługi Strona 10
- Strona / 30
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
FOR THE PLUMBER
The recommended water supply line is a 3/8-inch
O.D. copper tubing with a minimum operating
pressure of 20 PSIG and a maximum of 80 PSIG.
Connect to cold water supply line with standard
plumbing fittings, with shut off valve installed in an
accessible place between the water supply and
the cuber. In some cases a plumber will be
required.
Water Limitations:
An ice machine is a food manufacturing plant, it
takes in a raw material, water, and turns it into a
food product, ice. The purity of the water is very
important in obtaining pure ice and in maximizing
product life. Even though there isn’t one filter that
will cure all water problems, a good filter combined
with a polyphosphate feeder gives about the best
overall performance.
DRAIN
Connections: All drains are gravity type and must
have a minimum of 1/4-inch fall per foot on
horizontal runs. The drains to be installed to
conform with the local plumbing code. Install a
vertical open vent on drain line high point to insure
good draining. The ideal drain receptacle is a
trapped and vented floor drain. Recommended bin
drain is 5/8 inch O.D. copper tubing and should be
vented and run separately. Insulation for high
humidity areas is recommended.
The ice machine sump drain is 3/4" FPT. There
must be a vent at this connection for proper sump
draining.
WATER SUPPLY AND DRAIN CONNECTION
Maintain The Code
Required Air Gap
Between Drain Lines
And Building Drain
BIN DRAIN
Note: Some
Bins Drain Out
The Bottom
Vent
3/8" Male
Flare
Sump Drain Must
Be Vented
Optional
Filter
Potable
Water
Supply
Hand Shut
Off Valve
3/4" FPT
CME650R
March 1994
Page 10
- INTRODUCTION 1
- FOR THE INSTALLER 2
- Installation 3
- INSTALLATION 5
- TIGHTENING THE QUICK CONNECTS 6
- FOR THE ELECTRICIAN 7
- KCMR230 Installation 8
- KCMR230: Phasing Check 9
- FOR THE PLUMBER 10
- FINAL CHECK LIST 11
- COMPONENT LOCATION 12
- CONTROL BOX 13
- Water System Components 14
- INITIAL START UP 15
- FREEZING CYCLE OPERATION 17
- REFRIGERATION SCHEMATIC 18
- CLEANING & SANITIZING 19
- CLEANING 20
- SYSTEM SPECIFICATIONS 21
- ADJUSTMENTS 22
- SERVICE DIAGNOSIS: Water 23
- March 1994 24
- October 1994 25
- REMOVAL AND REPLACEMENT 26
- REFRIGERATION SERVICE: R-404A 29
- REFRIGERATION SERVICE 30
Powiązane produkty i podręczniki dla Kostkarki do lodu Scotsman CME650R
Kostkarki do lodu Scotsman MCM1062 Dokumentacja
(29 strony)
(29 strony)
Kostkarki do lodu Scotsman CME1002W Dokumentacja
(27 strony)
(27 strony)
Kostkarki do lodu Scotsman FME1204 Dokumentacja
(32 strony)
(32 strony)
Kostkarki do lodu Scotsman CMS1002R Dokumentacja
(27 strony)
(27 strony)
(2 strony)
(2 strony)BENDIX TCH-074-000 manuels
Manuels d'utilisation et guides de l'utilisateur pour Non BENDIX TCH-074-000.
Nous fournissons des manuels en pdf 1 BENDIX TCH-074-000 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji